CAMO 0345020 Manuel d'instructions télécharger pdf

!"#$%&&%$'(")!"#$*+,$'("#

-./0

)/%*2#3%"

)4567

Installation Instructions CAMO Marksman Edge

The CAMO Hidden Deck Fastening System is easy to use on treated wood,

hardwood, cedar, composite or PVC deckboards, to create a beautiful, fasten-

er-free deck surface.

The CAMO Marksman Edge is a versatile screw guide, designed specically for

installing treated wood decking tight together with no gap between the boards,

or the gap of your choice when used with secondary spacers. No pre-drilling is

required. These instructions will share the simple process of installing boards

with no gap.

Note: CAMO Hidden Fasteners, CAMO Tools and CAMO Driver Bits are

engineered to work exclusively together. Using other branded tools, fasteners

or bits will impair performance and not produce the desired results.

Before beginning installation of your deck, you will need the following:

• CAMO Hidden Fasteners (use 1-7/8" for 3/4" - 1-1/4"

deckboards; use 2-3/8" for 1-1/2"-2" deckboards)

• CAMO Marksman Edge

• Drill (set to the highest speed for maximum driving

efciency)

• Optional: Secondary Spacers if a gap is desired, and “L

Brackets” or 2-1/2’’ x #7 CAMO Exterior Trimhead Premium

Deck Screws for the board abutting the structure

,%3()/%*2#3%")7567)#,973%$',:

!"#$

#"%&'#"()*+,*

1. Drive Connection

2. Bit Change Nut

3. Driver Bit

4. Spring

5. Slide Tube

6. Body

7. Thumb Well

8. Tool Face

9. Screw Guide

%$$%,9'"6)$97)/%*2#3%")7567:

Insert the Marksman Edge Drive Connection into the drill. Be sure

to hold the Body of the Marksman Edge when powering the drill.

6%;)(;$'("#:

The CAMO Marksman Edge allows for multiple gap options when installing

deckboards. For treated lumber, the zero gap option allows builders to butt

deckboards tightly together. If a gap is desired, secondary spacers may be used

between the boards.

$97)<(%*5)%<+$$'"6)$97)#$*+,$+*7:

To begin deck installation, lay the rst board that abuts the structure into position and

fasten the outside edge at each joist using the Marksman Edge as instructed below. If

the abutting board runs parallel to the house /structure, it may be necessary to face

fasten the edge abutting the structure. If so, we recommend using 2-1/2’’ x #7 CAMO

Exterior Trimhead Premium Deck Screws. To avoid face fastening, use galvanized “L

Brackets” to fasten the board from below.

&(%5:

Fully insert one CAMO Hidden Fastener into the Screw Guide. The

Screw Guide is magnetized and will hold the screw in place.

For the outer edge of the deckboard, align the Screw Guide with

the joist below the deckboard (we recommend a minimum of 1’’

from board ends). Place the Marksman Edge so that the Tool Face

is at with the surface of the deckboard and the Screw Guide is

tight to the edge of the deckboard.

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

#7$:

For the inside edge of the deckboard, align the Screw Guide with the joist below

the deckboard, positioning the Screw Guide between the two adjoining

deckboards. Make sure that the Tool Face is at with the surface of the deckboard

and the Screw Guide is tight to the edge of the deckboard.

Set your driver to the highest speed.

Grip the driver drill in one hand, and hold the Marksman Edge in the other hand,

placing your thumb on the Thumb Well to ensure that the Tool Face is at with the

surface of the deckboard.

With the hand holding the Marksman Edge, snug the Screw Guide rmly against the radius of the edge

of the deckboard and hold in place. The Marksman Edge should remain tight against the board to avoid

tool movement or push back, as this can alter the angle and depth of drive. Firm pressure is required.

With the hand holding the drill, use light drive pressure and run the drill at full RPM - do not force the

screw. Allow the screw to spin and auger the surface. After a moment, the screw will grab and pull into

the board.

When driven fully and correctly, the nished position of the screw should be just below the surface of

the edge as shown to the left below.

Once you have fastened the rst screw on the outside edge of the deckboard, continue this process

down the length of the board. Repeat the same drive instructions on the inside edge of the deckboard

until the entire plank is installed. Do not skip any joists.

Example: fully driven Example: not fully driven

5*'=7:

,9%"6'"6)$97)5*'=7*)<'$:

<+$$)>('"$#:

We recommend blocking the joist at the butt joint and fastening 1’’ from the ends of the boards.

?@A)."6&7)!"#$%&&%$'("#:

Position the Marksman Edge over the edge of the high side of the joist so that the fastener remains

completely in the joist when fully driven. You may nd it useful to mark the deckboard where it

intersects the joist. To do this, draw a line where the deckboard intersects the joist and position the

Marksman Edge so the middle of the Screw Guide rests on the line. Proceed to drive the screw per the

instructions above. Repeat this process down the length of the deckboard on both edges.

To view an installation video or for more information, go to

www.camofasteners.com or contact us at (800) 968-6245

Unscrew the Bit Change

Nut and remove the bit

holder from the Slide

Tube, leaving the Spring

inside the Slide Tube.

Remove the old Driver Bit by pulling it rmly.

It should pop out.

Insert the replacement Driver Bit, making

sure it snaps into place.

To reassemble, hold the Slide Tube

extended as far as possible. Screw the Bit

Change Nut into the Slide Tube, compress-

ing the Spring inside.

1 2 3

!"#$ 1

Résumé du contenu

Page 1 - !"#$

!"#$%&&%$'(")!"#$*+,$'("#-./01)/%*2#3%"1)45678Installation Instructions CAMO Marksman Edge The CAMO Hidde

Page 2

Instrucciones para instalación de la camo® marksman® edge™Instrucciones para la instalación de la CAMO® Marksman® Edge™ El sistema CAMO de sujetación

Page 3

Directives d'installation du système CAMO® Marksman® EdgeDirectives d'installation du système CAMO® Marksman® EdgeLe système de xation invi

Commentaires sur ces manuels

Pas de commentaire

CAMO 0345020 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non CAMO 0345020. CAMO 0345020 Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non CAMO 0345020